M&D Repair Services
← All articles How to Diagnose Excavator Issues: A Step-by-Step Guide How-to

How to Diagnose Excavator Issues: A Step-by-Step Guide

Table of Contents

Last Updated: October 12, 2026

Safety First: Before You Diagnose

Heavy equipment can cause serious injury or death. The most common serious injuries when you diagnose excavator issues come from stored hydraulic pressure released when a line is opened, high-pressure fluid injection through the skin, and crush or pinch points from a dropping attachment or rolling machine.

The pre-diagnosis shutdown sequence

Follow this order every time:

  1. Park on level ground, lower the bucket and attachment, and set controls to neutral.
  2. Idle a few minutes to cool the turbo and hydraulic oil, then shut down.
  3. Cycle the control levers through every function with the engine off to bleed residual pressure, the step most people skip.
  4. Turn the battery disconnect to OFF or disconnect the negative cable so the machine cannot start.
  5. Lock out and tag out per your site's energy-control procedure; if you are the only operator, keep the key on your person.
  6. Install any manufacturer boom or arm safety locks before going under a raised attachment. Do not rely on hydraulics to hold it.
Watch Out Hydraulic oil can remain pressurized for hours after shutdown, and it can be hot enough to cause severe burns. Crack fittings slowly and wrap them in a rag to catch the release. Never use your hand to search for a leak, use a piece of cardboard or paper.

High-pressure injection is a medical emergency

A pinhole leak can inject fluid through the skin at pressures far exceeding what a hospital can easily treat. The wound may look like a small scratch, it is not. If fluid is injected into your hand or arm, go to an emergency room immediately and tell staff it was a hydraulic injection injury. Delayed treatment can lead to amputation or worse.

Personal protection and site setup

  • Wear steel-toed boots, work gloves, safety glasses, and hearing protection.
  • Keep bystanders clear of the swing radius and a Class ABC fire extinguisher within reach.
  • Use a spotter around the undercarriage or under a raised attachment, and never work alone if you can avoid it.

Stop-work criteria

Stop immediately and call a qualified technician if any of these occur during diagnosis:

  • Fluid sprays or streams from a fitting, hose, or cylinder.
  • The boom, arm, or bucket drifts or drops without a control input.
  • You smell burning oil, fuel, or electrical insulation.

If you are not confident, stop and call a professional.

Excavator Won't Start Troubleshooting

An excavator that won't start is usually a fuel or electrical problem. Start simple.

Check the fuel system:

  • Check the fuel gauge, is the tank empty or nearly empty?
  • Smell the fuel; stale fuel has a weak odor and won't burn properly.
  • Check the fuel filter for water or debris, which clogs it and prevents starting.

Check the battery and electrical connections:

  • Check battery terminals for white, blue, or green crusty corrosion; clean with a wire brush and reconnect tightly.
  • If the engine cranks slowly or clicks, the battery is weak.
  • Check visible wiring for loose connections, cuts, or burn marks.

Listen to the starter motor:

  • Does the starter crank the engine when you turn the key? If you hear nothing, the starter may be dead or its connection broken.
  • If it cranks but won't fire, move to fuel system diagnosis.

Most no-starts come down to a dead battery, corroded connections, or contaminated fuel. If the engine cranks normally but won't start, suspect fuel delivery or ignition timing.

Excavator Low Power Diagnosis

Low power means the engine runs but feels sluggish, slow boom, struggling travel motors. The trick is figuring out whether the fault is in the engine, hydraulics, or electrical control system, because the symptom looks the same from the seat.

Start with a symptom-to-system map

Before you open anything, narrow the complaint:

  • Engine bogs down or stalls under load, but functions are smooth when they move → fuel, air, or engine derate.
  • Engine holds RPM, but one function is slow or weak → hydraulic circuit or control input for that function.
  • Engine holds RPM, but all functions are slow → main pump, main relief, or a system-wide derate.

Write down what you observe. That note is the most useful thing you can hand a technician later.

Check the air and fuel path

  • Remove the air filter (usually a large cylindrical element on top of the engine) and hold it to a light source. If no light passes through, it's clogged, replace it.
  • Check the restriction indicator if fitted; a tripped indicator means the element is loaded.
  • Inspect the fuel filter, a restricted filter starves the engine under load and often shows up first as low power, not a no-start.

Read the exhaust and listen to the engine

  • White smoke: coolant burning or misfire.
  • Blue smoke: oil burning.
  • Black smoke: too much fuel for available air, often turbo, air filter, or injector.

Check the electrical and control side

This is the step most owners skip, and where many "low power" complaints actually live.

  • Battery and charging: A weak battery or failing alternator can make the engine control module reset or derate. A healthy 12-volt battery reads about 12.6 volts at rest and stays above roughly 10 volts while cranking; a 24-volt system reads about double. If it sags below that, load-test or replace it.
  • Fuses and relays: Inspect fuses for the engine control module, fuel pump, and throttle. Look for a blown fuse, corroded relay socket, or a relay that clicks but does not pass current.
  • Wiring and connectors: Look for chafed harnesses, green corrosion, and loose grounds, a bad ground causes intermittent derates that are hard to reproduce.

Check hydraulic pressure with a gauge

Do not judge hydraulic pressure by feel. Use a calibrated gauge rated above the system's relief setting, connect it to the manual's test port, and compare to the manufacturer's spec for that circuit and oil temperature.

  • Low at the main relief: relief valve stuck open or set wrong.
  • Low in one function only: that circuit's valve section or cylinder.
  • Low across all functions: main pump, suction leak, or system-wide derate.
Pro Tip Take pressure readings at normal operating temperature, not cold. Cold oil reads high and can mask a worn pump. Record the oil temperature alongside the pressure so the numbers mean something later.

Decide what to do next

If the air filter, fuel filter, fuel quality, battery, and fuses check out, the problem is likely in the hydraulic system, engine management system, or a sensor feeding it. You then need the correct service manual, a pressure gauge, and a way to read fault codes. If you don't have those, stop and call a technician, guessing at a derate by swapping parts gets expensive fast.

Excavator Hydraulic Problems Troubleshooting

The hydraulic system moves the boom, arm, bucket, and travel motors, and hydraulic problems are the most common complaint we hear.

Professional technician checking hydraulic fluid level in excavator reservoir with dipstick, examining fluid color and clarity under bright shop lighting
Professional technician checking hydraulic fluid level in excavator reservoir with dipstick, examining fluid color and clarity under bright shop lighting

Hydraulic Fluid Level and Condition

Check the hydraulic fluid level before every shift. Low fluid causes slow movement and overheating; dirty fluid damages pumps and valves.

How to check hydraulic fluid:

  • Locate the hydraulic reservoir (usually a large tank on the side or rear of the machine) and its dipstick or sight gauge.
  • Wipe the dipstick clean with a lint-free cloth, insert it fully, remove, and read the level, it should sit between the minimum and maximum marks.

What the fluid color tells you:

  • Bright amber or light tan: fluid is clean and in good condition
  • Dark brown or black: fluid is contaminated and needs replacement
  • Milky or cloudy: water has entered the system (a serious problem)

Contaminated hydraulic fluid destroys pumps, valves, and cylinders. If the fluid is dark or milky, drain and replace it immediately, new fluid costs far less than a hydraulic pump.

Hydraulic Leaks and Pressure Issues

Hydraulic leaks reduce pressure and cause slow movement, and a small leak becomes a big problem quickly.

Visual inspection for leaks:

  • Look under the excavator after it sits for an hour, fresh drips are easy to spot.
  • Check visible hoses for wet spots or dripping.
  • Inspect the boom, arm, and bucket cylinders for fluid on the rod or barrel.

Common leak locations:

  • Hose connections at the boom cylinder
  • Fittings at the control valve
  • The hydraulic pump seal

Pressure relief valve problems:

Call Us Today →

  • If the boom or arm drifts slowly downward without control input, the relief valve is leaking internally, wasting pressure and reducing performance. Clean or replace it.

Slow or jerky movement:

  • Slow movement usually means low pressure from a leak or worn pump.
  • Jerky movement (sudden stops and starts) usually means air in the lines, entering through loose connections or a low fluid level. Tighten visible connections and top up the fluid.

Check hoses and connections weekly, and replace any hose showing cracks, bulges, or wet spots.

Excavator Slow Travel Troubleshooting

The excavator moves slowly or won't move at all, while the boom works fine.

Check the hydraulic fluid level:

  • Low fluid is the most common cause of slow travel. Top up the reservoir; if the level drops again within hours, you have a leak.

Listen to the travel motors:

  • If you hear nothing when you move the travel controls, the control valve may be stuck or the electrical signal broken.
  • If you hear the motors but tracks move slowly, the motors are worn or pressure is low.

Inspect the final drive:

  • The final drive is the gearbox transferring power from the motor to the track sprocket. Oil leaking from it may mean internal damage, which causes slow travel and unusual noise.

Check track tension:

  • Loose tracks increase rolling resistance and slow the machine. Grab the track midway between the sprocket and idler wheel; you should be able to lift it about 2-3 inches.
  • If too loose, adjust the idler wheel to tighten it; if too tight, the final drive works harder and wears faster.

Look for bent or broken track links:

  • Walk around the excavator and inspect each link. Bent links cause vibration and slow movement; broken links are obvious, and a single broken link means the entire track must be replaced.

Slow travel is often a simple fix: top up the hydraulic fluid and check track tension. If that doesn't solve it, the problem is likely inside the final drive or travel motor, and you'll need professional help.

Undercarriage and Track Inspection

The undercarriage supports the entire excavator, and damaged tracks and parts cost thousands to repair.

Inspect the track:

  • Look for missing, bent, or cracked links. A missing link is an emergency, the track will come off and damage the undercarriage. Bent links cause vibration and noise. Replace damaged links before operating.

Check track alignment:

  • The track should run straight along the idler wheel and sprocket. If it pulls to one side, adjust the idler wheel to center it; misalignment causes uneven wear and slow travel.

Look at the sprocket:

  • Teeth should be even and sharp. Worn, rounded teeth cause the track to slip, and broken teeth mean the sprocket must be replaced.

Check the idler wheel:

  • It should roll smoothly by hand. If stiff or noisy, the bearing is worn, causing misalignment and uneven wear.

Inspect the frame and pins:

  • Look for cracks in frame welds and check pins and bolts for looseness. Loose pins let the undercarriage shift, causing track problems. Tighten to the manufacturer's specification.

Inspect tracks and undercarriage every 50 operating hours, small problems caught early are cheap fixes, while ignored problems become major breakdowns.

When to Stop Work and Call for Service

Some problems are too serious to diagnose yourself. Stop work immediately if you see these warning signs:

Stop work if:

  • The engine overheats (temperature gauge in the red zone)
  • Hydraulic fluid is spraying or leaking heavily
  • The boom or arm moves unexpectedly without your input

These indicate serious damage, and continuing to operate risks catastrophic failure and injury.

Call for professional service when:

  • Basic checks are complete and the problem persists
  • You're unsure what's causing the symptom
  • The machine needs parts you don't have

Call for professional service when:

  • Basic checks are complete and the problem persists
  • You're unsure what's causing the symptom
  • The machine needs parts you don't have

Frequently Asked Questions

What are the most common reasons an excavator won't start?

Starting issues typically stem from three sources: fuel system problems (empty tank, contaminated fuel, clogged fuel filter), battery or electrical failures (dead battery, corroded terminals, faulty starter), or engine compression loss. Check fuel level and condition first, then verify battery voltage. If the engine cranks but won't fire, the issue is likely fuel or ignition-related. If it won't crank at all, focus on electrical connections and battery health.

How do I diagnose low power in an excavator?

Low power diagnosis requires checking three systems in order: fuel delivery (clogged air filter or fuel filter restricts flow), hydraulic pressure (measure with a gauge; low pressure indicates pump or valve problems), and engine load (verify the engine isn't struggling under normal operating conditions). Start with visual inspections of filters, then move to hydraulic pressure testing if filters are clean. Engine compression testing may be needed if pressure is normal.

What should I check first when an excavator has a hydraulic problem?

Always start with hydraulic fluid level and condition. Low or contaminated fluid causes most hydraulic failures. Inspect the reservoir, check fluid color (dark or milky indicates contamination), and verify the level matches the dipstick mark. Next, visually inspect hoses, fittings, and cylinders for active leaks. If fluid is low and you find no leaks, the pump or control valves may be failing internally. Only then move to pressure testing.

Why is my excavator moving slowly or jerking?

Slow or jerky movement in the boom, arm, or bucket usually points to hydraulic issues: low fluid, contaminated fluid, weak pump output, or failing control valves. Slow travel (movement across the ground) often indicates track tension problems, final drive wear, or travel motor failure. Inspect hydraulic fluid first, then check track tension and alignment. If hydraulics appear normal, the final drive or travel motor may be damaged, requiring professional diagnosis.


Diagnosing excavator issues takes patience and a systematic approach. Start with the simplest checks: fuel, air, hydraulic fluid, and electrical connections. Most problems are caught early this way. For complex hydraulic, engine, or undercarriage issues, professional diagnosis saves time and money. M&D Repair Services specializes in mobile heavy equipment repair and can diagnose excavator problems at your location with free estimates and warranty on all work performed.